Exactly How to Remove and Change a Bathtub
Exactly How to Remove and Change a Bathtub
Blog Article
Almost everyone has their own individual idea when it comes to A Step-by-Step Guide to Installing a Bathtub.
Mounting a tub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably tough project. If the old bathtub is easily available, the task can relocate quickly; if you need to open a wall to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Ensure you have certified yourself for the work as well as are comfortable trying it. Instead of hiring a service provider to take control of a halfway-completed project, it is far better to think about using one before you start. Chances are you may require an expert plumber to make tube links.
This short article will certainly help you set up a new tub in your washroom if you have currently acquired a new bathtub and also don't require to change the plan of your previous water pipes.
Your tools as well as product checklist must comprise the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be quite problematic because of the limited access that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. Once the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former type should be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using both wood boards under its feet, position the tub in the needed setting. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub until the spirit level reviews degree.
To set up taps, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water and also examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill up the tub and also check the overflow outlet and the regular electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub needs to wait up until the tub has been made use of at the very least when as this will resolve it right into its final position.
Preparing for the Installment
To start with, the supporting structure provided with the bath should be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final setting.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to break a stiff seal, creating the water to pass through the wall between the bath as well as the tiling, bring about difficulties with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched paper or soft rope. Remember to always fill the tub with water before sealing, to enable the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently offered on the market. It is recommended to fit the tiles making use of waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very fascinated with Installing A Bathtub and I'm hoping you enjoyed reading our blog posting. If you enjoyed our blog entry please make sure you remember to pass it around. I recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
This Page
Report this page